Printronix T4204 Bedienungsanleitung Seite 132
- Seite / 232
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
132
Chapter 3 LinePrinter Plus Emulation
LinePrinter Plus P-Series Emulation
Control Code 06
Control Code 06 defines the function of ASCII code hex 06 (ACK). You can
select an alternate line spacing of 6, 8 or 10.3 LPI.
Control Code 08
Control Code 08 defines the function of ASCII code hex 08 (BS). You can
define the code to output an elongated character or a backspace.
Define CR Code
This option controls the action of the printer when it receives a Carriage
Return code (hex 0D) from the host computer. If this feature is enabled, each
time the printer receives a Carriage Return, it inserts an additional Line Feed
code (hex 0A) into the data stream. Do not use this feature if the host
computer sends Line Feeds to the printer.
• CR = CR. Does not insert an extra Line Feed after each Carriage Return.
• CR = CR + LF. Inserts an extra Line Feed after each Carriage Return.
The next print position will be print position 1 of the next line.
Printer
Protocol
(from page 125)
Control Code
06
Control Code
08
Define CR
Code
Auto LF
Overstrike Define LF
Code
Select SFCC
EVFU Select Alt. Set 80-9F
Character Set
6.0 LPI
8.0 LPI*
10.3 LPI
Elongated*
Backspace
CR = CR*
CR = CR + LF
Disable*
Enable
Enable*
Disable
LF = CR + LF*
LF = LF
1*
(0-7F hex)
Enable*
Disable
Control Code*
Printable
(see page 135)
* = Factory Default
P-Series
SFCC d
Command
PSeries
Dbl High
Even dot plot*
Double high
Normal *
P3/4/6/9 Compat
FF Valid at
TOF
Enable*
Disable
- User’s Manual 1
- T4204 Label Printer 1
- Software License Agreement 3
- Communication Notices 5
- Trademark Acknowledgements 7
- PRINTER WARRANTY 8
- THERMAL PRINTHEAD 8
- SUPPLIES 8
- ON-SITE MAINTENANCE SERVICE 8
- Table of Contents 12
- 1 Introduction 13
- The T4204 Label Printer 14
- Thermal Printer Technology 15
- Media Selection 16
- Emulations 16
- Hardware Options 17
- Unpacking The Printer 18
- Check List 20
- Printer Installation 21
- 2) Bail lock 23
- 2 Operation 25
- The POWER Switch 26
- Powering On The Printer 26
- Operating Modes 27
- Primary Control Panel Keys 27
- Secondary Control Panel Keys 27
- Loading Media 28
- Loading Roll Media 29
- Chapter 2 Loading Roll Media 30
- Loading Fanfold Media 34
- Loading Ribbon 38
- Chapter 2 Loading Ribbon 40
- Label Rewinding 41
- Chapter 2 Label Rewinding 42
- 1) Label Rewinder Spindle 43
- 2) Label Rewind Clip 43
- Label Peel Off 44
- Chapter 2 Label Peel Off 46
- Run Calibrate Procedure 49
- Cleaning The Printhead 50
- 3 Configuring The Printer 51
- Chapter 3 Menu Navigation 54
- Selecting A Menu Option 55
- Changing Printer Settings 56
- Saving A Configuration 57
- 6 key until: 58
- Printing A Configuration 60
- Menu Options 65
- Chapter 3 Menu Options 66
- 4) key to move to 66
- 3) key to go back to a 66
- Active IGP EMUL Menu 67
- Emulation Menu 68
- MAINT / MISC Menu 69
- Downloaded Fonts 71
- File System 71
- Cancel Key 71
- Auto Locking 71
- Set Lock Key 72
- Auto Label Map 73
- Auto Map Select 73
- Example 2: Uneven Number Case 74
- Example 3: Blank Label Case 75
- Compatibility 76
- Power Saver Time 76
- HOST INTERFACE Menu 77
- Auto Switching 78
- Report Status 79
- Centronics (Parallel) 80
- Interface Type 82
- Data Protocol 82
- Baud Rate 84
- Word Length 84
- Stop Bits 84
- Poll Response 86
- Idle Response 86
- One Char Enquiry 86
- Printer Status 87
- Prime Signal 88
- TOF Action 88
- Buffer Size In K 88
- Ethernet 89
- ETHERNET PARAMETERS Menu 90
- Printer Control Menu 91
- Page Width 92
- Page Length 92
- Print Speed 93
- Print Intensity 93
- Print Mode 93
- Media Sensor 93
- Media Handling 94
- Paper Feed Shift 94
- Hor Image Shift 94
- Ver Image Shift 94
- Calibrate 95
- Tear-Strip Time 96
- Clip Page 96
- Error Recovery 96
- Font Memory Menu 97
- Max Char Memory 98
- Max Cache Memory 98
- Max Cache Size 99
- Max Cached Char 99
- Max Fonts Loaded 99
- Font Weight 99
- Installed Fonts 99
- DIAGNOSTICS Menu 100
- System Memory 101
- Print Statistics 101
- IGP/PGL Emulation 102
- IMPORTANT 103
- (see page 111) 104
- (see page 108) 104
- Define LF Code (Line Feed) 105
- Autowrap 105
- Select SFCC 105
- PI Slew Range 105
- Chapter 3 IGP/PGL Emulation 106
- example, at 6 lpi there is 106
- Skip Command Prefix 107
- Power On IGP/PGL 107
- Extended Execute Copy 107
- Barcode Options 108
- Host Form Length 109
- PGL Normal 109
- Do FF at TOF 110
- IGP 100 Compatibility 110
- Ignore Character 110
- Error Report 110
- IGP/PGL Character Set Menu 111
- IGP/VGL Emulation 112
- (see page 116) 114
- (see page 123) 114
- Page Format 115
- Graphics Options 116
- Chapter 3 IGP/VGL Emulation 118
- Width Limit 118
- Absorb After ^PN 118
- Error Handling 119
- Ignore / DB8 Setup 119
- Ignore Chars 120
- Ignore Ch#1 120
- Ignore Ch#2 120
- Data Bit 8 120
- Resolution 121
- Font Options 121
- PI Control 121
- Max PI 16 122
- IGP/VGL Character Set Menu 123
- LinePrinter Plus Emulation 124
- (see next page) 124
- (see page 130) 124
- (see page 132) 125
- Printer Protocol 126
- Orientation 126
- CPI/LPI Select 127
- Font Attributes 127
- Text Position 129
- Plot Attributes 129
- (see page 135) 132
- Overstrike 133
- Define LF Code 133
- EVFU Select 133
- Alt. Set 80-9F 134
- Character Set 134
- SFCC d Command 134
- PSeries Dbl High 134
- FF Valid at TOF 134
- P-Series Character Set Menu 135
- Control Code 06 136
- Define CR Code 136
- Slew Relative 138
- (see page 141) 139
- Character 140
- Sets Reference Manual 140
- (see page 144) 142
- FF Valid At TOF 143
- 20 CPI Condensed 143
- (see page 147) 145
- Printer Select 146
- Coax/Twinax Emulation 148
- (see page 150) 148
- • System 3x 149
- • AS/400 149
- • 3270 Mainframes 149
- (see page 151) 150
- Char Set Select 151
- Translation Table 151
- Active Char Set 151
- Buffer Reprint 152
- Device ID 152
- SCS Buffer Control 152
- Early Print Complete 152
- Cancel IGP/DCU 153
- PTX Transparent Control 153
- Change Case 153
- Set Text Orientation 153
- Compatibility Options 154
- Image Buf Size 154
- Intervention Req 154
- Translate Table 156
- Host Override 156
- Format Control 157
- Max. Print Width 157
- Buffer Print 157
- Device Address 160
- 5225 World Trade 160
- PTX Transparent 160
- Graphic Chek Err 161
- Graphic Chek Code 161
- LAC Option 161
- LAC Approx 161
- Set Text Orientn 161
- SPC Coax Params 163
- SPC Twx Params 165
- SPC Type 166
- Loading Flash Memory 167
- FILENAME.ZIP 168
- FILENAME 168
- FILENAME.EXE 169
- XXXXXXXX 173
- 4 Interfaces 177
- Centronics Parallel Interface 178
- IEEE 1284 Parallel Interface 180
- Removal And Installation 184
- 5 Diagnostics And 187
- • Hardware Handshaking 188
- • Software Handshaking 189
- Controlling Print Quality 190
- Other Printer Problems 191
- • Printer fails to turn on 193
- Printer Alarms 194
- Fault Messages 194
- Maintenance Manual 195
- A Specifications 201
- Appendix A 202
- Front of Printer 203
- Lists Of Approved Media 204
- Indicators And Switches 204
- Host Interfacing 204
- Electrical: 204
- Environmental: 205
- Physical: 205
- Options: 205
- B Printer Options 207
- Interface Options 208
- Supplies And Accessories 209
- Genuine Printronix Media 210
- Accessories 212
- C Setting The Page Length 213
- Appendix C 214
- • If the application does 214
- D ASCII Control Codes 215
- Appendix D 216
- XON = Ctrl Q (DC1) 217
- XOFF = Ctrl S (DC3) 217
- E Glossary 219
- Numerics 223
- Visit our website at: 232
- 750514-001E 232
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.005 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern