Printronix T4204 Bedienungsanleitung Seite 49
- Seite / 232
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
49
Run Calibrate Procedure
NOTE: Verify that the media installed in the printer matches the PRINTER
CONTROL menu Media Sensor option (Transmissive or Reflective).
Verify that the transmissive sensor is horizontally positioned to permit
sensing of the notch, gap, or black stripe. (See “Sensor Assembly
Horizontal Adjustment” on page 47.)
1.
Press and release the PAUSE key to place the printer offline.
2.
Open the printer front door to allow access to the Secondary Control
Panel.
3.
Press and release the UP and DOWN (
5 and 6) keys simultaneously to
unlock the printer menu. “ENTER SWITCH UNLOCKED” appears on the
LCD.
4.
Press the NEXT (
4) key until “PRINTER CONTROL” appears on the
LCD.
5.
Press the DOWN (
6) key. “Page Width” appears on the LCD.
6.
Press the NEXT (
4) key until “Calibrate” appears.
7.
Press the DOWN (
6) key. “Run Calibrate” appears.
8.
Press the ENTER key. The media will advance a minimum of 11 inches
plus the distance required to detect three additional Top-of-Form
positions.
The procedure is completed successfully if no fault is displayed and the
Sensed Distance value is correct. See “Sensed Distance” on page 95 for
a detailed description of Sensed Distance.
NOTE: If a fault message such as “GAP NOT DETECTED” or “LOAD
PAPER” appears while performing the Run Calibrate procedure,
press the CLEAR key and perform the Run Calibrate procedure
again, by going back to Run Calibrate under the PRINTER
CONTROL main menu and then press the ENTER key.
9.
Press the UP (
5) key until “OFFLINE PRINTER CONTROL” appears on
the LCD.
10.
Press the FEED key. The media should advance one forms length.
NOTE: If the Page Length value is longer than the physical page length of the
media in use, the printer will continue to advance media to achieve
that Page Length value and then stop at the next TOF position.
11. Press the PAUSE key to place the printer Online.
- User’s Manual 1
- T4204 Label Printer 1
- Software License Agreement 3
- Communication Notices 5
- Trademark Acknowledgements 7
- PRINTER WARRANTY 8
- THERMAL PRINTHEAD 8
- SUPPLIES 8
- ON-SITE MAINTENANCE SERVICE 8
- Table of Contents 12
- 1 Introduction 13
- The T4204 Label Printer 14
- Thermal Printer Technology 15
- Media Selection 16
- Emulations 16
- Hardware Options 17
- Unpacking The Printer 18
- Check List 20
- Printer Installation 21
- 2) Bail lock 23
- 2 Operation 25
- The POWER Switch 26
- Powering On The Printer 26
- Operating Modes 27
- Primary Control Panel Keys 27
- Secondary Control Panel Keys 27
- Loading Media 28
- Loading Roll Media 29
- Chapter 2 Loading Roll Media 30
- Loading Fanfold Media 34
- Loading Ribbon 38
- Chapter 2 Loading Ribbon 40
- Label Rewinding 41
- Chapter 2 Label Rewinding 42
- 1) Label Rewinder Spindle 43
- 2) Label Rewind Clip 43
- Label Peel Off 44
- Chapter 2 Label Peel Off 46
- Run Calibrate Procedure 49
- Cleaning The Printhead 50
- 3 Configuring The Printer 51
- Chapter 3 Menu Navigation 54
- Selecting A Menu Option 55
- Changing Printer Settings 56
- Saving A Configuration 57
- 6 key until: 58
- Printing A Configuration 60
- Menu Options 65
- Chapter 3 Menu Options 66
- 4) key to move to 66
- 3) key to go back to a 66
- Active IGP EMUL Menu 67
- Emulation Menu 68
- MAINT / MISC Menu 69
- Downloaded Fonts 71
- File System 71
- Cancel Key 71
- Auto Locking 71
- Set Lock Key 72
- Auto Label Map 73
- Auto Map Select 73
- Example 2: Uneven Number Case 74
- Example 3: Blank Label Case 75
- Compatibility 76
- Power Saver Time 76
- HOST INTERFACE Menu 77
- Auto Switching 78
- Report Status 79
- Centronics (Parallel) 80
- Interface Type 82
- Data Protocol 82
- Baud Rate 84
- Word Length 84
- Stop Bits 84
- Poll Response 86
- Idle Response 86
- One Char Enquiry 86
- Printer Status 87
- Prime Signal 88
- TOF Action 88
- Buffer Size In K 88
- Ethernet 89
- ETHERNET PARAMETERS Menu 90
- Printer Control Menu 91
- Page Width 92
- Page Length 92
- Print Speed 93
- Print Intensity 93
- Print Mode 93
- Media Sensor 93
- Media Handling 94
- Paper Feed Shift 94
- Hor Image Shift 94
- Ver Image Shift 94
- Calibrate 95
- Tear-Strip Time 96
- Clip Page 96
- Error Recovery 96
- Font Memory Menu 97
- Max Char Memory 98
- Max Cache Memory 98
- Max Cache Size 99
- Max Cached Char 99
- Max Fonts Loaded 99
- Font Weight 99
- Installed Fonts 99
- DIAGNOSTICS Menu 100
- System Memory 101
- Print Statistics 101
- IGP/PGL Emulation 102
- IMPORTANT 103
- (see page 111) 104
- (see page 108) 104
- Define LF Code (Line Feed) 105
- Autowrap 105
- Select SFCC 105
- PI Slew Range 105
- Chapter 3 IGP/PGL Emulation 106
- example, at 6 lpi there is 106
- Skip Command Prefix 107
- Power On IGP/PGL 107
- Extended Execute Copy 107
- Barcode Options 108
- Host Form Length 109
- PGL Normal 109
- Do FF at TOF 110
- IGP 100 Compatibility 110
- Ignore Character 110
- Error Report 110
- IGP/PGL Character Set Menu 111
- IGP/VGL Emulation 112
- (see page 116) 114
- (see page 123) 114
- Page Format 115
- Graphics Options 116
- Chapter 3 IGP/VGL Emulation 118
- Width Limit 118
- Absorb After ^PN 118
- Error Handling 119
- Ignore / DB8 Setup 119
- Ignore Chars 120
- Ignore Ch#1 120
- Ignore Ch#2 120
- Data Bit 8 120
- Resolution 121
- Font Options 121
- PI Control 121
- Max PI 16 122
- IGP/VGL Character Set Menu 123
- LinePrinter Plus Emulation 124
- (see next page) 124
- (see page 130) 124
- (see page 132) 125
- Printer Protocol 126
- Orientation 126
- CPI/LPI Select 127
- Font Attributes 127
- Text Position 129
- Plot Attributes 129
- (see page 135) 132
- Overstrike 133
- Define LF Code 133
- EVFU Select 133
- Alt. Set 80-9F 134
- Character Set 134
- SFCC d Command 134
- PSeries Dbl High 134
- FF Valid at TOF 134
- P-Series Character Set Menu 135
- Control Code 06 136
- Define CR Code 136
- Slew Relative 138
- (see page 141) 139
- Character 140
- Sets Reference Manual 140
- (see page 144) 142
- FF Valid At TOF 143
- 20 CPI Condensed 143
- (see page 147) 145
- Printer Select 146
- Coax/Twinax Emulation 148
- (see page 150) 148
- • System 3x 149
- • AS/400 149
- • 3270 Mainframes 149
- (see page 151) 150
- Char Set Select 151
- Translation Table 151
- Active Char Set 151
- Buffer Reprint 152
- Device ID 152
- SCS Buffer Control 152
- Early Print Complete 152
- Cancel IGP/DCU 153
- PTX Transparent Control 153
- Change Case 153
- Set Text Orientation 153
- Compatibility Options 154
- Image Buf Size 154
- Intervention Req 154
- Translate Table 156
- Host Override 156
- Format Control 157
- Max. Print Width 157
- Buffer Print 157
- Device Address 160
- 5225 World Trade 160
- PTX Transparent 160
- Graphic Chek Err 161
- Graphic Chek Code 161
- LAC Option 161
- LAC Approx 161
- Set Text Orientn 161
- SPC Coax Params 163
- SPC Twx Params 165
- SPC Type 166
- Loading Flash Memory 167
- FILENAME.ZIP 168
- FILENAME 168
- FILENAME.EXE 169
- XXXXXXXX 173
- 4 Interfaces 177
- Centronics Parallel Interface 178
- IEEE 1284 Parallel Interface 180
- Removal And Installation 184
- 5 Diagnostics And 187
- • Hardware Handshaking 188
- • Software Handshaking 189
- Controlling Print Quality 190
- Other Printer Problems 191
- • Printer fails to turn on 193
- Printer Alarms 194
- Fault Messages 194
- Maintenance Manual 195
- A Specifications 201
- Appendix A 202
- Front of Printer 203
- Lists Of Approved Media 204
- Indicators And Switches 204
- Host Interfacing 204
- Electrical: 204
- Environmental: 205
- Physical: 205
- Options: 205
- B Printer Options 207
- Interface Options 208
- Supplies And Accessories 209
- Genuine Printronix Media 210
- Accessories 212
- C Setting The Page Length 213
- Appendix C 214
- • If the application does 214
- D ASCII Control Codes 215
- Appendix D 216
- XON = Ctrl Q (DC1) 217
- XOFF = Ctrl S (DC3) 217
- E Glossary 219
- Numerics 223
- Visit our website at: 232
- 750514-001E 232
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.988 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern